CCJKQ - P/N 8600 ACCELERATOR SHORT CUT AUTO GLASS ADHESIVE/SEALANT
- MSDS: CCJKQ
- Manufacturer: MINNESOTA MINING AND MFG CO AUTOMOTIVE TRADES DIV
- Product Name: P/N 8600 ACCELERATOR SHORT CUT AUTO GLASS ADHESIVE/SEALANT
- National Stock Number: 8040-00D020016
Product Identification
Product ID:P/N 8600 ACCELERATOR SHORT CUT AUTO GLASS ADHESIVE/SEALANT
MSDS Date:03/08/1992
FSC:8040
NIIN:00D020016
Kit Part:Y
MSDS Number: CCJKQ
Responsible Party
ST PAUL, MN 55144-1000
US
Emergency Phone: 612-773-1110
Info Phone: 612-733-1110
Cage: 52157
Contractor
Telephone: 414-255-5520
Cage: 050Q3
Ingredients
URETHANE PREPOLYMER
CAS: 68610-33-3
Fraction By Weight: 50-60%
METHYLENE BISPHENYL ISOCYANATE (MDI) (SARA 313)
CAS: 101-68-8
RTECS: NQ9350000
Fraction By Weight: 20-30%
OSHA PEL C 0.02 PPM
ACGIH TLV: 0.005 PPM; 9596
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
HYDROGENATED TERPHENYLS
CAS: 61788-32-7
RTECS: WZ6535000
Fraction By Weight: 10-20%
OSHA PEL 0.5 PPM
ACGIH TLV: 0.5 PPM; 9596
DIMETHYL SILOXANE, REACTION PRODUCT WITH SILICA OR SILICON
CAS: 67762-90-7
Fraction By Weight: 1-10%
OSHA PEL 6 MG/M3
ACGIH TLV: 10 MG/M3
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:EXPOSURE MAY CAUSE EYE & SKIN
IRRITATION. MAY CAUSE ALLERGIC RESPIRATORY REACTION IN SOME PERSONS
IF INHALED. INGESTION MAY CAUSE GI TRACT IRRITATION. CHRONIC: NONE
SPECIFIED BY MANUFACTURER.
Explanation of Carcinogenicity:NO INGREDIENT OF A CONCENTRATION OF 0.1%
OR GREATER IS LISTED AS A CARCINOGEN OR SUSPECTED CARCINOGEN.
Effects of Overexposure:EYES-IRRITATION. SKIN-IRRITATION.
INHALED-ALLERGIC RESPIRATORY REACTION. INGESTED-GI TRACT
IRRITATION.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:IN ALL CASES GET MEDICAL ATTENTION. EYES-FLUSH WITH WATER FOR
15 MINUTES. SKIN-FLUSH WITH LOTS OF WATER. INHALED-REMOVE TO FRESH
AIR. INGESTED-DO NOT INDUCE VOMITING! IF CONSCIOUS, DRINK 2 GLASSES
WAT ER. CALL A PHYSICIAN.
Fire Fighting
Flash Point:>300F,>149C
Extinguishing Media:WATER, CARBON DIOXIDE, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS AND
FULL FIRE FIGHTER'S PROTECTIVE GEAR.
Unusual Fire/Explosion Hazard:NONE.
Accidental Release
Spill Release Procedures:VENTILATE AREA. OBSERVE PRECAUTIONS IN OTHER
SECTIONS OF MSDS. ONLY PROPERLY TRAINED PERSONS SHOULD ENTER SPILL
AREA. ISOLATE & DENY ENTRY. COLLECT SPILLED MATERIAL, PLACE IN
CONTAINER & SEAL.
Neutralizing Agent:DILUTE AMMONIA SOLUTION (90% WATER, 8 AMMONIUM
HYDROXIDE, 2 & LIQUID DETERGENT)
Handling
Handling and Storage Precautions:KEEP CONTAINER TIGHTLY CLOSED. KEEP
OUT OF REACH OF CHILDREN. USE IN A WELL-VENTILATED AREA. AVOID SKIN
CONTACT. AVOID EYE CONTACT.
Other Precautions:FOR INDUSTRIAL OR COMMERCIAL USE ONLY. DO NOT INGEST.
AVOID PROLONGED BREATHING OF PRODUCT.
Exposure Controls
Respiratory Protection:IF ENGINEERING CONTROLS FAIL OR NON-ROUTINE USE
OR AN EMERGENCY OCCURS; WEAR AN MSHA/NIOSH APPROVED AIR-SUPPLIED
RESPIRATOR OR SCBA, AS REQUIRED. USE IAW 29 CFR 1910.134.
Ventilation:USE IN A WELL-VENTILATED AREA. USE ADEQUATE MECHANICAL
VENTILATION OR LOCAL EXHAUST TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:IMPERVIOUS-RUBBER, PLASTIC.
Eye Protection:SAFETY GLASSES/CHEMICAL SPLASH GOGGLES.
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER. DLA-HMIS:
EYE WASH STATION & SAFETY SHOWER.
Work Hygienic Practices:WASH HANDS AFTER HANDLING AND BEFORE EATING,
DRINKING, OR SMOKING. LAUNDER CONTAMINATED CLOTHES BEFORE REUSE.
Supplemental Safety and Health
KEY1=N1. THIS ACCELERATOR USED WITH BASE (DOCUMENT NUMBER 11-0428-0).
Chemical Properties
HCC:N1
Boiling Pt:B.P. Text:392F,200C
Vapor Pres:0.000
Vapor Density:8.60
Spec Gravity:1.010
Appearance and Odor:WHITE, THIXOPTROPIC PASTE; PUNGENT ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
REACTS WITH WATER (ATMOSPHERIC & LIQUID); AMINE, ALCOHOL-- NOT A
HAZARD.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CARBON MONOXIDE AND CARBON DIOXIDE,
HYDROGEN CYANIDE, NITROGEN OXIDES, POSSIBLE ISOCYANATES, SMOKE
PARTICLES.
Conditions to Avoid Polymerization:WILL NOT OCCUR.
Disposal
Waste Disposal Methods:FOR ACCELERATOR OR MIXED PARTS ONLY: FULLY CURED
OR NEUTRALIZED WASTE MAY BE DISPOSED OF IN A SANITARY LANDFILL.
INCINERATE UNUSED OR PARTIALY CURED BULK MATERIAL AFTER MIXING WITH
FLAMMABLE MATERIAL IN AN INDUSTRIAL OR COMMERCIAL FACILITY.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.